Ford F-150 Roof Rack Installation Guide: Step-by-Step (2015–2020)
A cab roof rack turns your F-150 into a real overland and work platform: rooftop tent, lights, recovery boards and gear, all mounted up top and out of the bed. Because this rack bolts into drilled, rivnut-reinforced mounting points, the installation is what makes it rock-solid and leak-free for years.
This is the official AEGON installation guide for the Ford F-150 roof rack. It covers the full process in six steps: assembling the rack on the ground, marking and drilling the roof, installing rivnuts, sealing the brackets and the final torque sequence. You can also download the full PDF manual to keep in your truck.
✅ The short answer
Assemble the rack on the ground with bolts finger-tight, mock it up on the roof and mark the bracket holes, drill with a stop collar (1/8" pilot, then 11 mm), install and fully expand the rivnuts, seal every bracket and bolt with silicone, then mount the rack and torque from the bottom up. Plan on 2 to 3 hours and two people.
📄 Download the Official Installation Manual (PDF)
3 pages with package contents, required tools and all six installation steps with a verification check for each one. Print it or save it on your phone before you start.
Download the PDF Guide📋 In this guide
- Installation at a glance
- Safety and preparation
- Package contents and required tools
- Step 1: Assemble the rack on the ground
- Step 2: Roof mock-up and hole marking
- Step 3: Drill the roof mounting holes
- Step 4: Install the rivnuts
- Step 5: Install brackets with silicone
- Step 6: Final mounting and torque sequence
- FAQ
1. Installation at a Glance
| Item | Details |
|---|---|
| Difficulty | Moderate |
| Estimated time | 2 – 3 hours |
| People required | 2 |
| Compatible racks | AEGON Aluminum and Steel Ford F-150 roof racks (2015–2020) |
| Mounting | Drilled roof mounting points with threaded rivnuts and silicone sealant |
2. Safety and Preparation
⚠️ Important safety warning
Drilling into your roof requires extreme care. Always check interior headliner clearance before drilling and wear safety glasses. Make sure every rivnut is fully expanded and sealed with silicone to prevent structural loosening and water leaks.
3. Package Contents and Required Tools

| Qty | Component |
|---|---|
| 1x | Front wind deflector |
| 2x | Side rails (sidebars) |
| 4x | Crossbars (numbered 1 through 4) |
| 4x | Mounting brackets |
| 1 kit | Complete hardware kit (bolts, washers, nuts) |
| 1 pack | Threaded rivet nuts (rivnuts) |
| 1x | Manual rivnut installation tool (grade bolt, drive nut, friction washer) |
| 1 tube | Waterproof silicone sealant |
Tools you'll need (not included)
- Power drill
- 1/8" pilot drill bit
- 11 mm (7/16") drill bit
- Drill bit stop collar
- 13 mm and 14 mm open-end wrenches
- Allen keys and hand wrenches
- Center punch or marker
- Measuring tape and masking tape
4. Step 1: Assemble the Rack on the Ground
Pre-assembly
Build the complete rack on a soft, scratch-free surface or assembly table before it goes on the truck.
- Attach the 4 crossbars to the two side rails in order from front to back, following their numbers (1 through 4).
- Attach the front wind deflector to the front of the side rails.
- Keep all hardware finger-tight so the frame can adjust during the mock-up.
✅ Verification
The rack is fully assembled with the crossbars in order 1 to 4 and all bolts finger-tight.
5. Step 2: Roof Mock-Up and Hole Marking
2 people required
- Apply masking tape to the roof channel areas where the brackets will sit to protect the paint.
- With two people, carefully lift the assembled rack onto the roof.
- Center it front-to-back and side-to-side with a measuring tape.
- Mark the center of each bracket mounting hole on the tape with a center punch or permanent marker.
- Carefully remove the rack from the truck.
✅ Verification
Hole marks are clear, centered in the channels and identical on the driver and passenger sides.
6. Step 3: Drill the Roof Mounting Holes
Use a drill stop
- Set a drill stop on the 1/8" pilot bit so it can't plunge into the headliner or side air curtains, and drill a pilot hole at each mark.
- Switch to the 11 mm (7/16") bit, also with a drill stop, and enlarge each hole.
- Vacuum the metal shavings and apply touch-up paint or rust inhibitor to the exposed metal edges.
✅ Verification
Holes are clean and let the rivnut body slide in flush without forcing it.
7. Step 4: Install the Rivnuts with the Manual Tool
13 mm & 14 mm wrenches
- Thread a rivnut onto the manual installation tool (grade bolt, drive nut and friction washer).
- Insert the rivnut fully into a hole until its lip sits flush against the roof skin.
- Hold the drive nut still with the 14 mm wrench while turning the grade bolt with the 13 mm wrench until the rivnut expands and crushes firmly against the underside of the sheet metal.
- Unscrew the tool and repeat for every hole.
✅ Verification
Every rivnut is locked completely tight to the roof panel, with zero spinning or play when checked by hand.
8. Step 5: Install the Brackets with Silicone Sealant
Waterproofing
- Apply a generous ring of waterproof silicone around and inside each rivnut opening.
- Place the mounting brackets over the rivnuts.
- Coat the threads and the underside of each bolt head with silicone before threading it into the rivnut.
- Tighten the bracket hardware securely.
✅ Verification
A visible bead of silicone has formed under each bracket base and around every bolt head.
9. Step 6: Final Rack Mounting and Torque Sequence
Bottom-to-top order

- With two people, lift the rack onto the secured brackets.
- Fasten the side rails to the brackets.
- Working from bottom to top, fully torque all hardware in this order: first the bracket-to-roof bolts, then the bracket-to-side-rail bolts, and finally all crossbar and wind deflector bolts.
🔧 Final inspection
Grab the rack firmly and shake it. The truck's suspension should move with the rack, with zero flex, play or rattling at any joint.
10. FAQ
Do I need to drill my F-150's roof?
Yes. This rack mounts to drilled attachment points reinforced with threaded rivnuts for maximum strength. Everything you need for the mounting points (rivnuts, installation tool and silicone) is included; the drill and bits are not.
How long does the installation take?
Plan on 2 to 3 hours with two people.
How do I make sure the roof won't leak?
Seal every rivnut opening with a generous ring of silicone, coat the bolt threads and the underside of the bolt heads before installing them, and touch up any bare metal around the drilled holes.
What if a rivnut spins?
A rivnut that spins has not been fully expanded. Hold the drive nut with the 14 mm wrench and keep turning the grade bolt with the 13 mm wrench until it locks tight against the sheet metal.
How do I keep the drill bit from damaging the headliner?
Check headliner clearance first and use a drill stop collar on both the 1/8" pilot bit and the 11 mm bit.
Need help with your install?
Tell us your F-150's year and cab configuration and where you're stuck. Our team will walk you through it.
Talk to the AEGON Team