Jeep Grand Cherokee Roof Rack Installation Guide: Step-by-Step (WJ/WG 1999–2004)

Jeep Grand Cherokee Roof Rack Installation Guide: Step-by-Step (WJ/WG 1999–2004)

The WJ/WG Grand Cherokee is one of the most capable classic Jeeps for overlanding, and a full-length roof rack is what unlocks its cargo potential: rooftop tent, recovery gear, fuel cans and lights, all off the cabin floor. The difference between a rack that stays quiet and dry for years and one that whistles or leaks comes down to how it is installed.

This is the official AEGON installation guide for the Jeep Grand Cherokee roof rack. It walks you through bench assembly, mounting on the factory roof points, sealing against water and the correct torque sequence to avoid wind noise. You can also download the full PDF manual to keep in your Jeep.

✅ The short answer

Assemble the rack on the bench with all bolts loose, place the closed brackets at the front and the open-gap brackets at the rear factory points, seal every mounting hole with silicone (including the unused center hole), set the rack on with two people, then tighten from the bottom up: brackets, sidebars, front deflector, and finally crossbars and rear deflector.

📄 Download the Official Installation Manual (PDF)

3 pages with package contents, bench assembly, vehicle mounting, weatherproofing and the final torque sequence. Print it or save it on your phone before you start.

Download the PDF Guide

1. Installation at a Glance

Item Details
Vehicle Jeep Grand Cherokee WJ / WG (1999–2004)
Compatible racks AEGON Steel and Aluminum Grand Cherokee roof racks
Mounting Bolts to the factory roof mounting points with 4 brackets (2 front, 2 rear)
People required 2 (to lift and position the rack)
Sealing Automotive silicone sealant on every mounting hole, plus the unused center hole

2. Before You Start: The Key Principle

⚠️ Don't tighten anything yet

Do not fully tighten any bolt during the initial assembly phases. Leave all hardware slightly loose so the structure can align and adjust. Apply final torque only after the entire rack is correctly positioned and mounted on the vehicle.

3. Package Contents

AEGON full-length roof rack for Jeep Grand Cherokee WJ

Qty Component
2 Main sidebars (left and right)
5 Crossbars
2 Front roof brackets (flat / completely closed)
2 Rear roof brackets (with a gap / open space between the holes)
1 Front wind deflector
1 Rear deflector
1 Protective rubber trim (front deflector only)
1 kit Mounting hardware (bolts, flat washers and nuts)

4. Phase 1: Bench Assembly and Preparation

Assemble the rack on a clean, flat, protected surface (blankets, cardboard or foam) so you don't scratch the finish.

Step 1: Prepare and fit the front wind deflector

  1. Install the rubber trim on the bottom edge of the deflector (the edge that touches the roof) before mounting it. The cushioned bulb, the thicker side, faces inward toward the back of the deflector.
  2. Lay the sidebars parallel to each other.
  3. Position the deflector so its side mounting tabs sit on the inside of both sidebars.
  4. Insert the bolts from the outside and add the flat washer and nut on the inside. Hand-tighten only so you can adjust the height later.

Step 2: Install the crossbars

  1. Space the 5 crossbars evenly along the rack, aligned with the sidebar mounting holes.
  2. Leave an even gap between crossbars (for example, one empty mounting hole between each) for better weight distribution.
  3. Install the hardware at each end and snug it loosely.

Step 3: Install the rear deflector

  1. Position the rear deflector at the back of the rack.
  2. Alignment: its side tabs go on the inside of the sidebars, while its top flange sits flat on top of the sidebars.
  3. Secure it loosely with the supplied bolts.

✅ Check before moving on

The rack is fully assembled on the bench with evenly spaced crossbars, and every bolt is still loose enough to adjust.

5. Phase 2: Vehicle Mounting and Weatherproofing

Step 1: Identify the brackets and prepare the roof

  1. Place the 2 flat, completely closed brackets on the front mounting points of the roof.
  2. Place the 2 brackets with a gap between the holes on the rear factory mounting points.
  3. Leak prevention: before securing the brackets, apply a generous amount of high-quality automotive silicone around and directly into the mounting holes to create a permanent, watertight seal.

🛡️ Seal the unused center hole

The Grand Cherokee has an extra threaded hole in the center channel of the roof that this rack does not use. Seal it: fill the thread with silicone or, ideally, install a short bolt coated in silicone to close the port permanently against water.

Step 2: Secure the rack to the roof

  1. With a second person, lift the assembled rack and set it onto the roof brackets.
  2. Make sure the main sidebars sit on the outside of the brackets.
  3. Insert the bolts that join the sidebars to the brackets.

6. Phase 3: Torque Sequence and Noise Prevention

AEGON low-profile roof rack installed on a Jeep Grand Cherokee WJ

Once the rack is aligned and resting in its final position, tighten everything in a strict bottom-up order to eliminate wind noise and structural stress:

  1. First: tighten the brackets down to the roof mounting points.
  2. Second: tighten the bolts connecting the brackets to the sidebars.
  3. Third (crucial for noise): before tightening the front deflector bolts, press the deflector down firmly until the rubber trim is fully compressed and flush against the roof. Keep that pressure while you fully tighten the side bolts. This seal breaks the airflow and prevents whistling and high-speed vibration.
  4. Fourth: fully tighten all 5 crossbars and the rear deflector hardware.

🔧 Final inspection

  • Do a final visual check to confirm the rack sits symmetrically on the roof.
  • Re-check the torque on every fastener after the first 60 miles (100 km) of driving.

7. FAQ

Do I need to drill my Grand Cherokee's roof?

No. The rack mounts on the Jeep's factory roof mounting points using the included front and rear brackets.

Which brackets go in front and which go in the rear?

The flat, completely closed brackets go on the front mounting points. The brackets with a gap between the holes go on the rear mounting points.

How do I prevent roof leaks?

Apply automotive silicone around and into every mounting hole before securing the brackets, and seal the unused threaded hole in the center channel with silicone or a short silicone-coated bolt.

Why is my roof rack whistling?

Almost always it's the front deflector. Loosen its side bolts, press it down until the rubber trim is fully compressed against the roof, and retighten while holding the pressure.

Do I need to re-tighten the bolts later?

Yes. Re-check every fastener after the first 60 miles (100 km).

Need help with your install?

Tell us your Grand Cherokee's year and where you're stuck. Our team will walk you through it.

Talk to the AEGON Team
📍 Based in Orlando, FL 🏕️ Built for Overland Camping 💬 Real Support from Our Team

Read next